BLOWER VIBRATION ANALYSIS TUTORIAL

Blower Vibration Analysis

Blower Vibration Analysis Software

Centrifugal Blower • Roots Blower • Positive Displacement Blower • Industrial Fan

1. Blower Construction & Vibration Fundamentals

Centrifugal Blower

Air or gas enters through the inlet and is accelerated by an impeller. Common components include motor, coupling, bearings, shaft, impeller, casing and foundation.

Roots Blower

Two synchronized lobed rotors move gas through the casing. Timing gears, rotor clearances, shaft bearings and lubrication are important inspection areas.

Multistage Blower

Multiple impellers or stages are arranged on a shaft. Check rotor balance, shaft dynamics, interstage conditions, bearing condition and coupling alignment.

Important vibration quantities

ParameterUnitMeaning
FrequencyHzCycles per second
Velocity RMSmm/sCommon machine vibration severity measurement
Accelerationm/s² or gUseful for high-frequency impacts and bearing condition
Displacementµm or mmRotor movement / low-frequency vibration
CPMCycles/minFrequency × 60
OrderXFrequency divided by running frequency

2. Blower Vibration Measurement Points

PointLocationDirectionPurpose
P1Motor DE bearingH / V / AMotor bearing, coupling and unbalance
P2Motor NDE bearingH / V / AMotor bearing and structural vibration
P3Blower DE bearingH / V / ABlower shaft and bearing condition
P4Blower NDE bearingH / V / ABearing, rotor and alignment condition
P5Gearbox input shaftH / V / AGear mesh and input bearing
P6Gearbox output shaftH / V / AGear mesh and output bearing
P7Casing / supportH / VStructural resonance and looseness

H = Horizontal, V = Vertical, A = Axial. Follow the machine manufacturer's measurement locations and sensor mounting instructions.

3. RPM, Frequency & Harmonics Calculator

4. FFT Spectrum Analysis Simulator

Choose a fault to view a typical illustrative spectrum. This is not an actual measured FFT.

Actual FFT requires time waveform data, sampling frequency, sensor calibration, appropriate windowing and correct amplitude scaling.

5. Bearing Defect Frequency Calculator

Theoretical frequencies may differ from actual measured values because of rolling element slip, load and bearing geometry. Use manufacturer data where available.

6. Gearbox Frequency Calculator

For a simple gear pair: output RPM = input RPM × input teeth / output teeth. For multistage gearboxes, calculate each gear mesh separately.

7. Blower Fault Diagnosis & Corrective Actions

FaultTypical spectrum indicationPossible causeRecommended action
UnbalanceDominant 1X, often radialDust deposits, uneven impeller wear, damaged rotorClean rotor, inspect blades and check balance
Misalignment1X / 2X, axial may be highMotor-blower coupling alignment errorCheck alignment, coupling and soft foot
Mechanical loosenessMultiple harmonics, impactsLoose bolts, bearing housing or foundationInspect bolts, baseplate, bearing fits and supports
Bearing damageBPFO, BPFI, BSF, FTF and harmonicsRaceway damage, lubrication failure, contaminationEnvelope analysis, inspect lubrication and bearing
Gear mesh problemGear mesh frequency and sidebandsWorn teeth, backlash, poor lubricationInspect gear teeth, backlash and oil condition
Blade / lobe passBlade or lobe pass frequencyBlade damage, aerodynamic excitation, rotor interactionInspect blades/lobes, clearances and operating condition
Surge / instabilityLow-frequency fluctuations, broadband energyUnstable flow, low flow, system resistanceReview operating map, flow, pressure and control system
ResonanceLarge narrow peakStructural or rotor natural frequencyCheck phase, run-up/coast-down and structural stiffness
Rotor rubbingHarmonics, subharmonics, impactsRotor-stator contact, thermal expansion, clearance issueInspect clearances, shaft movement and temperature
Electrical motor issuePossible 2× line frequency, sidebandsElectrical asymmetry, air-gap eccentricityCheck motor current, voltage balance and electrical condition
Belt drive issueBelt frequency, 1X and harmonicsLoose belt, pulley misalignment, belt damageCheck tension, alignment and belt condition

Blower-specific inspection checks

  • Check inlet filter, silencer, ducting and outlet restriction.
  • Inspect impeller blades for dust accumulation, erosion, cracks and deposits.
  • Check bearing lubrication, temperature, clearance and housing condition.
  • Check coupling or belt condition and alignment.
  • For Roots blowers, inspect timing gears, rotor clearances and synchronization.
  • Check pressure, flow, temperature and operating point against OEM limits.
  • For centrifugal blowers, review surge margin and aerodynamic stability.

8. Vibration Severity Comparison

ISO vibration evaluation depends on machine type, power, speed, mounting and measurement location. Select the applicable ISO 20816 part and OEM criteria.

ZoneGeneral meaning
ATypically acceptable for newly commissioned machines
BNormally acceptable for long-term operation
CGenerally unsatisfactory for continuous long-term operation
DVibration severe enough to risk machine damage
Important: Do not use one universal mm/s limit for every blower. ISO 20816-3 may be relevant to certain industrial machines, but verify scope and machine classification. Roots blowers and special-purpose machines may require other criteria or OEM limits.

9. Blower Inspection Record

10. Practical Frequency Example

Assume a centrifugal blower runs at 1480 RPM with 10 impeller blades.

  • Running frequency = 1480 / 60 = 24.67 Hz
  • 2X = 49.33 Hz
  • 3X = 74.00 Hz
  • 4X = 98.67 Hz
  • Blade pass frequency = 10 × 24.67 = 246.67 Hz

Useful formulas

  • Running frequency (Hz) = RPM / 60
  • Harmonic frequency = Running frequency × order
  • Blade pass frequency = Blade count × shaft frequency
  • Gear mesh frequency = Gear teeth × gear shaft frequency
  • CPM = Hz × 60
  • For a pure sine wave only: Peak velocity = RMS velocity × 1.414

11. Safety Precautions

  • Follow site permit-to-work and LOTO procedures before opening guards or touching equipment.
  • Never touch rotating shaft, coupling, belt or blower components.
  • Do not loosen bearing housing or casing bolts while running.
  • Use approved vibration measurement access points and safe sensor mounting.
  • For gas blowers, consider process gas toxicity, pressure, temperature and isolation risks.
  • Never exceed OEM operating limits during diagnostic testing.
Blower Vibration Analysis | Engineering learning and condition monitoring reference

Followers